Universal Aimbot 2.5 Beta - VAC Proof Forever Color Aimbot

[NeSuckS]

Short introduction: This little program will help you get headshots. All it does is take a lot of screenshots of the game, a little image analysis, then moves the mouse for you in MW3 or w/e game your playing. This aimbot is superior to other aimbots out there since it does a bit block transfer directly to an array, then the array is split into colors using minimal cpu usage. All other aimbots that I've encountered use getpixel which is about 200 times slower.

Release date: September 28, 2013 (2.5 Beta)

VAC status: VAC proof forever. It doesn't modify the game in any way. All it does is take screenshots of the game and move your mouse.

Requirements: There are 3 requirements that should be met.

1. You will need colored skin player models which a material/texture wallhack has, the models can be any color.

2. .NET framework 4.0 is required. You should have it already through windows update.

3. Run MW3 in WINDOWED MODE.


Solution to problems:

The aimbot is not targeting dark colors
Check the "Target Darker Colors" Check box under settings.
The aimbot is shaking too much
Lower the aimbot sensitivity and disable any mouse acceleration
Change graphic settings to increase FPS to over 60
Try using the default aimbot settings instead of playing with the numbers
Disable V-SYNC
The Aimbot does nothing at all
Make sure raw mouse input in is disabled
You need a colored player model to target, look at the picture below to see what I mean
DISABLE ALL ANTI-ALIASING!
Run the game in windowed mode
Run the game in windowed mode
Run the game in windowed mode
Try turning DWM off/on in the settings tab
The aimbot keeps aiming upward
Your crosshair is the same color as what you are trying to target, why don't you set the crosshair to another color?
The aimbot aims too slowly
Increase the aimbot sensitivity
What settings should I use with the default aimbot settings
Windows mouse sensitivity should be on the 6th notch, windows enhanced precision disabled, and mouse acceleration disabled.

What settings you should look out for:

Disable vertical sync
not doing so will cause the aimbot to aim very badly.
Disable anti-aliasing
Aimbot won't work with it enabled in fullscreen mode.
Disable RAW mouse imput
Aimbot won't work with it enabled.
Disable motion blur
Causes smearing which could throw the aimbot off.
Disable HDR
Can cause more smearing with transparent textures.
Very transparent wallhack
Very transparent wallhacks can cause severe color smearing in certain areas of maps.
Anything less than 65 FPS (or monitor HZ)
will cause the aimbot to wobble and shake regardless of sensitivity. The aimbot works well with 100-200 FPS.
Windows enhanced pointer precision
Not good with low FPS
Mouse filter
Probably should be disabled since it will average mouse movements making tracking strafing enemies more difficult
Windowed mode
If the aimbot doesn't work after changing the screenshot method, run the game in windowed mode.
UA aimbot sensitivity
You will definitely need to adjust this and find the correct sensitivity. The correct sensitivity also changes for different screen resolutions. Later vers I plan on having the aimbot find the correct setting. Keep raising the sensitivity if the aimbot is failing to track far enemies strafing and lower if the aimbot is shaking too much.
Amount to shift down/Amount to shift right
These can be set to negative values. The amount to shift down should be set more when sniping since enemies are enlarged.
Multi-core rendering
Enable this, it will increase your FPS if you got a multi-core cpu.






MW3 will probably need to be ran in windowed mode for this aimbot to work! You also need chams/textures to target. For other full screen games, change the screenshot method from GetForegroundWindow to GetActiveWindow. When in windowed mode, you no longer need to move MW3/CS:S to the middle of the monitor, the aimbot will aim in the center of the game regardless of where MW3 is on your monitor.

Change Log: The aimbot now calculates what color you're trying to target and is now able to target darker colors and exclude brighter colors with the wrong tint. It's now able to calculate what a bright texture would be if it were in shade and be able target it.

Virus total scan: VirusTotal - Free Online Virus, Malware and URL Scanner

Jotti virus scan: UA2.5 Beta.zip - Jotti's malware scan

[[MPGH]Hero]

Approved .

[MLG_ProTryhard]

wats new? from the other version?

[Lovroman]

wats new? from the other version?

Changelog:
The aimbot now calculates what color you're trying to target and is now able to target darker colors and exclude brighter colors with the wrong tint. It's now able to calculate what a bright texture would be if it were in shade and be able target it.

[NeSuckS]

This one is much different than any color aimbot out there. For example if you target RED and the min color for RED is 190, it'll go as low as 80-90ish for RED color if the max color for green and blue matches the ratio when red was at 190.

For example, if your settings were:
RED: 190-255
BLUE: 0-65
GREEN: 0-65

You'll notice the maxcolor for blue/green is 65, which is 34% the mincolor for red. With this aimbot, a red color of 100 will trigger it if blue and green is below 34. Also, If the aimbot comes across a color that's a different tint, it'll not target it, even if it's in the color range you want to target. Had to do all this because mat fullbright models are hard to come by these days.

[CONTROL007]

where release models?

[Fightera100]

Don't works. It aims randomly in the sky and not on my enemies...

[NeSuckS]

Don't works. It aims randomly in the sky and not on my enemies...

Never played MW3 so I dunno. Maybe the sky is blue and you're trying to target blue or your cross-hair is blue.

Try making the aimbot target a deeper blue with these settings:
RED: 0 - 35
BLUE: 220-255
GREEN: 0 - 35

[Fightera100]

Never played MW3 so I dunno. Maybe the sky is blue and you're trying to target blue or your cross-hair is blue.

Try making the aimbot target a deeper blue with these settings:
RED: 0 - 10
BLUE: 245-255
GREEN: 0 - 10

Ty for the answer but i won't try that because i already deleted this aimbot and i dont play mw3 anymore

[staffie]

your other aimbot is detected in mw3, maybe this will be aswell just a heads up .

[UltimateG4M3R]

hmm cool D

[FavioS]

Good Work dude~!

[DemoN.7]

how to remove the dead bodies from the multiplayer iw5m ?

[xIINRage]

How can I use it?? It doesnt work.

[ImMalkah]

your other aimbot is detected in mw3, maybe this will be aswell just a heads up .

It is not detected. It is a color aimbot and does not interfere with the memory aspect of the game, therefore it will be forever undetected.