ForsakenBotBeta V4 (1440p)

[3andrew]

Here is my latest work in progress. I hope you find it's much better than my last attempt. There are still some minor quirks (see below) that I'm in the progress of working out. This bot is a modified version based on the original AHK bot that has been spread around. This was created and tested for use on 1440p, though 1080p settings have been included but are untested and may need some minor adjusting.




Known Issues

1. Mars and Nessus are still a huge pain. Bot may at times snap to unexpected locations (though fairly minimal)
2. Speed. I've successfully dwindled down to a single image, but due to size it can be slow at times. Specifically on planets listed in point 1.
3. Under some situations, it can snap to the enemy's capture point in control PvP.


Images

https://imgur.com/a/RVE5iKj
https://imgur.com/a/gXL1CNE


Virus Scans

https://www.virustotal.com/#/file/8d...37a6/detection
https://www.garyshood.com/virus/resu...9b4fbf138517cd

[[MPGH]Ahl]

Approved.

This has not been tested.

[JackAim]

well for me its working worse than fatdob version, i think its couse i use rare resolution 1680x1050 and i dont sure how to change image to make it work

[ricardmark1]

Seems worse.
and no 1080p is a no go for me.
Fatdoobie version way more consistent.

Nevertheless, good atempt. Keep searching for the good formula.
But fixing on only a tested resolution is detrimental.

1440p and 1080p should be consistent.

[3andrew]

Seems worse.
and no 1080p is a no go for me.
Fatdoobie version way more consistent.

Nevertheless, good atempt. Keep searching for the good formula.
But fixing on only a tested resolution is detrimental.

1440p and 1080p should be consistent.

Unfortunately I do not own a 1080p display so I'm unable to test settings for it. But can you share your experience with a little more detail? Is it wobbling around, not locking, ect?


I'm going to copy a post I made in the larger thread. It may help some people with adjusting 1080p settings.



Sensitive - how fast the bot tries to correct. Too high and it gets wobbly, too slow and it lags far behind. The sensitivity number in the settings.ini you use must be adjusted if you change the in game sensitivity.

FOV - Is essentially the box size of the scan area. The smaller the better here but too small and someone can move outside the box and cause it to loose lock.

Aim x and y - this is the offset of aim from the target lock. Since we are locking to a health bar, we need to adjust to aim center mass on the head. I wouldn't mess with the x axis unless you are adjusting for 1080p but you can adjust the y. I prefer aiming mid neck to account for recoil so I prefer a larger deviation from the aim point. This means the y number must be larger. I believe I use around 60 for that.

[JackAim]

its almost not lock for me...

[haduyhung]

You can add triggerbot.?thank you

[DeliriousHD]

Unfortunately I do not own a 1080p display so I'm unable to test settings for it. But can you share your experience with a little more detail? Is it wobbling around, not locking, ect?


I'm going to copy a post I made in the larger thread. It may help some people with adjusting 1080p settings.



Sensitive - how fast the bot tries to correct. Too high and it gets wobbly, too slow and it lags far behind. The sensitivity number in the settings.ini you use must be adjusted if you change the in game sensitivity.

FOV - Is essentially the box size of the scan area. The smaller the better here but too small and someone can move outside the box and cause it to loose lock.

Aim x and y - this is the offset of aim from the target lock. Since we are locking to a health bar, we need to adjust to aim center mass on the head. I wouldn't mess with the x axis unless you are adjusting for 1080p but you can adjust the y. I prefer aiming mid neck to account for recoil so I prefer a larger deviation from the aim point. This means the y number must be larger. I believe I use around 60 for that.

Cant you quite literally go to your display settings and CHANGE it to 1080p. https://prntscr.com/l08sim <---

[OldTimeGmer]

Here is my latest work in progress. I hope you find it's much better than my last attempt. There are still some minor quirks (see below) that I'm in the progress of working out. This bot is a modified version based on the original AHK bot that has been spread around. This was created and tested for use on 1440p, though 1080p settings have been included but are untested and may need some minor adjusting.




Known Issues

1. Mars and Nessus are still a huge pain. Bot may at times snap to unexpected locations (though fairly minimal)
2. Speed. I've successfully dwindled down to a single image, but due to size it can be slow at times. Specifically on planets listed in point 1.
3. Under some situations, it can snap to the enemy's capture point in control PvP.


Images

https://imgur.com/a/RVE5iKj
https://imgur.com/a/gXL1CNE


Virus Scans

https://www.virustotal.com/#/file/8d...37a6/detection
https://www.garyshood.com/virus/resu...9b4fbf138517cd

nice work as always listed below is the 1080p setting i use on a 26" screen and works very well at least for me except for point 1 in org post esp Mars
[settings]
sen=4.5
FovX=4.3
FovY=3.5
AimX=85
AimY=52

hope it helps

[m4a_X]

nice work as always listed below is the 1080p setting i use on a 26" screen and works very well at least for me except for point 1 in org post esp Mars
[settings]
sen=4.5
FovX=4.3
FovY=3.5
AimX=85
AimY=52

hope it helps

In Gamble it not locking on the target, normal?

[boy]

How high can I go on the sens? or is it risky/bannable to go any higher than 5?

[m4a_X]

How high can I go on the sens? or is it risky/bannable to go any higher than 5?

Do not overdo it in PVP then the ban risk should be relatively low.

[slayerh4x]

Thank you very much. This one is amazing.

[boy]

Do not overdo it in PVP then the ban risk should be relatively low.

thanks for the reply, I pretty much will only be using this for pve though, so what sen= would you recommend?

[kaalaron]

nice work as always listed below is the 1080p setting i use on a 26" screen and works very well at least for me except for point 1 in org post esp Mars
[settings]
sen=4.5
FovX=4.3
FovY=3.5
AimX=85
AimY=52

hope it helps

What are your Red/White tolerance settings? I use it just fine in PvP, but i can't figure out good settings for PvE use