[wanted]new cheat engine tut

Posts 1–15 of 38 · Page 1 of 3

hey, could anyone post a full warrock cheat engine tut here or on an new topic?
i mean an full tut so not only weapons.
a tut like how to find values and addresses would be usefull.
if someone post some tut how to do that i can create hacks and post them here.
so post a tut and ill try to release sum hacks!

Originally Posted by killablade

Well...if you want to learn the basics of how to look for values and addresses...then a good place to start is by doing the Cheat Engine tutorials...then something like the weapon tutorials. You cant run before you can walk. For example, first off...go here and do ALL the cheat engine tutorials you can find...(including the actual CE tutorials): There is NO way on earth your gonna learn how to memory hack if you dont know how to use cheat engine properly first. (if CE is going to be your weapon of choice)

CE forum's are a GREAT place to learn how to use the software...and for learning how memory editing works.

http://forum.****************/index.php

Tutorials:

http://forum.****************/viewtopic.php?t=26540

Now once you have done all of those, try my tutorial on finding the pointers for your weapon addresses. This will give you a good working knowledge of scanning and how to understand pointers and some info on assembly calculations.

The tutorial is here http://mpgh.net/forum/showthread.php?t=4387

You will allready see that my tutorial on pointers is a direct carry on from one of those tutorials at CE...it uses the same technique. This is how I worked out the weapon pointers...because I did a tutorial on pointers first....and learned.

Now once you have done ALL the CE tutorials...and you have done my weapon tutorial..you should have a fairly good basic knowledge of memory editing and Cheat Engine...

So now try this:

Your mission is to try to find the address of the scope (zoom) for the sniper rifle. DONT use a tutorial or look up the address...use logic to work it out.

If you can find the scope address...you can find GPS/INF STAMINA/NO FALL DAMAGE...the addresses are VERY close together.

I will give you a hint....

Not zoomed in...the value would be 0
zoom level x 1...the value would be 1
zoom level x 2...the value would be 2

You see ? Its logical...something that is turned OFF is allways set to 0...something that is turned ON...is always 1 or higher.

Want another challenge? Why not try make a hack that allows you to fly (well kinda fly lol)

Here is your hint...its all about the stance your player is in......

Anyway, good luck....its not rocket science...but its not simple either. Just learn CE for a start...then try a few warrock tutorials for CE and you will begin to understand the concepts that go into memory editing ....THEN you can start working things out for yourself.

first tell me what cheat engine do you use?
cause with my cheat engine warrock crashes all the time.
i select warrock in the process list and then warrock crashes!

Originally Posted by killablade

first tell me what cheat engine do you use?
cause with my cheat engine warrock crashes all the time.
i select warrock in the process list and then warrock crashes!

Use UCE...there are copies out there ...you can find it if you look hard enough....also...you might want to try with the latest version of normal cheat engine..have been playing around with it, as it seems to scan faster...and so far...it appears to be undetected

ok i used warrock_cheats

Warrock_Cheats IS a UCE released by WELLington it should work fine.....if it keeps crashing your warrock...its most likley something with your PC

ok.
but warrock doesnt crashes when i do it in urban ops...
weird huh

well ok but if i do your tut(pointer tut) i get 3 addresses...
and if i do see what writes ... and i change back to my second slot i only get 1 thing showing up!
what do i have to do to do it right?
or is good what i did?

Originally Posted by killablade

Check your 3 addresses again...go back into warrock and switch weapons several times again...change to grenades...if both addresses dont show 42 now..then you have the wrong addresses....2 should say 42..and one should not be 42..delete that one.

U might want to wait until I update the tutorial...I have some extra info from Dave which should make all the weapons visible all the time.

ok...
when are you going to update the tut?
and is it ok if i do this just in urban ops so not in training?
cause everytime i do it in training warrock and warrock_cheats both crashes!
so i have did it in urban ops not in training.
and i get 3 addresses that always change when i change weapon.
for grenades 42 fists 1 they keep switching if i switch weapon.
so they are all weapon addresses.

do normal scan, then right click the address(s), and click see what writes to this address. then make the value go down and you'll see some addresses,

this was in the ce tut, but im not sure what to do from there, got too bored at reading...

but eh fortran can u post the gps and scope addresses and values here?
and the tut works but when i tried to make trainer it crashed.

Originally Posted by killablade

but eh fortran can u post the gps and scope addresses and values here?
and the tut works but when i tried to make trainer it crashed.

Nope...cant give you any addresses im afraid...thats why im trying to help people figure them out, as best i can anyay. As for it crashing when u tried to make a trainer...nevermind...if you followed the tutorial u saved your pointes as a CE cheat table..so go open then load them again and try make the trainer once more. You dont even need to have warrock running to make it. In the process box just type WarRock.exe

can i make it with cheat engine 5.3 to?
its detected but if i use the the addresses i got with my uce it might work.
cause everytime i try to make trainer and i klik generate trainer and save it it crashes!