[Forever VAC proof] Universal Aimbot 2.0 Beta 1.6

[RELEASE] Universal Aimbot 2.0 BETA 1.6

Short introduction: This little program will help you get headshots. All it does is take a lot of screenshots of the game, a little image analysis, then moves the mouse for you in cs:s. This aimbot is superior to other aimbots out there since it does a bit block transfer directly to an array, then the array is split into colors using minimal cpu usage. All other aimbots that I've encountered use getpixel which is about 200 times slower.

Release date: October 22, 2010 (2.0 beta 1.6)

VAC status: By the way it operates it is 100% VAC proof without a doubt. It doesn't modify the game in any way. All it does is take screenshots of the game and move your mouse.

Requirements: There are 2 requirements that should be met before you run this program.

1. You will need colored skin CT models or colored T models which a material wallhack has, the models can be any color.

2. .NET framework 4.0 is required. You should have it already through windows update.

Solution to problems:

The aimbot is targeting corpses
Type cl_ragdoll_physics_enable 0 in console
I don't know how to install the material wallhack
You are a n00b
The aimbot is shaking too much
Lower the aimbot sensitivity and disable any CSS mouse acceleration
Type cl_showfps 2 in console and change graphic settings to increase FPS to over 60
Try using the default aimbot settings instead of playing with the numbers
Disable V-SYNC
The Aimbot does nothing at all
Make sure raw mouse input in css is disabled
You need a colored player model to target, look at the picture below to see what I mean
DISABLE ALL ANTI-ALIASING!
Run CSS in windowed mode
Try turning DWM off/on in the settings tab
Try using another screenshot method in the settings 2 tab
The aimbot keeps aiming upward
Your crosshair is the same color as what you are trying to target, why don't you set the crosshair to green? by typing cl_crosshaircolor 0.
The aimbot aims too slowly
Increase the aimbot sensitivity
What settings should I use with the default aimbot settings
Windows mouse sensitivity should be on the 6th notch, windows enhanced precision disabled, the CSS mouse sensitivity your using should be entered in the aimbot, and CSS mouse acceleration disabled.

What settings you should look out for:

Disable vertical sync
not doing so will cause the aimbot to aim very badly.
Disable anti-aliasing
Aimbot won't work with it enabled.
Disable RAW mouse imput
Aimbot won't work with it enabled.
Disable motion blur
Causes smearing which could throw the aimbot off.
Disable HDR
Can cause more smearing with transparent textures.
Very transparent wallhack
Very transparent wallhacks can cause severe color smearing in certain areas of maps.
Anything less than 65 FPS (or monitor HZ)
will cause the aimbot to wobble and shake regardless of sensitivity, type cl_showfps 2 and lower settings until FPS is near or above 60 at all times.
No css mouse acceleration
CSS mouse acceleration isn't for noobs, but setting this to a small amount could help track strafing enemies.
Windows enhanced pointer precision
Not known if this effects CSS, prolly should keep it enabled to help track strafing enemies if it does do anything.
Mouse filter
Probably should be disabled since it will average mouse movements making tracking strafing enemies more difficult
Windowed mode
Always try and go fullscreen mode - You'll get more FPS and not have a window border. Try enabling / disabling DWM in the settings tab to see if fullscreen will work.
UA aimbot sensitivity
You will definitely need to adjust this and find the correct sensitivity. The correct sensitivity also changes for different screen resolutions. Later vers I plan on having the aimbot find the correct setting. Keep raising the sensitivity if the aimbot is failing to track far enemies strafing and lower if the aimbot is shaking too much.
Amount to shift down/Amount to shift right
These can be set to negative values. The amount to shift down should be set more when sniping since enemies are enlarged.
Multi-core rendering
Enable this, it will increase your FPS if you got a multi-core cpu.

So if your someone who had vertical sync enabled and said UA 1.57 sucked - now you know why.

Virus scan #1: UA 2.0 Beta 1.6.zip - Jotti's malware scan
Virus scan #2: Report - Antivirus online virus scan - viruschief.com
Virus scan #3: Metascan Online | Fast, free malware multi-scanning tool

As of now, virustotal is completely down and uploading a file to virscan results in 403 forbidden error

UA 2.0 Beta 1.6.zip ua2.0beta1.6.png

Originally Posted by dominator012

@NeSuckS scrap the motion aimbot. There is no point as when you move, it wont work unless there is a way to fix that. Wich there isnt as you are moving :S

No, I'm not scrapping it b/c its very promising. Game play isn't effected at all when you are moving. It's gonna be useful for snipers or watching a corner and it works the very instant you stop moving. I could make the aimbot press the "S" button for you when you stop pressing "W" to move back enough so you can come to a stop very fast, so you'll only get about a half second delay from UA color aimbot. The difference between motion aimbot and trigger aimbot is that the motion aimbot will record the color range of what it's about to shoot and track that color. So once it gets a color range to track - you can move and it'll work somewhat like a color aimbot. After a few secs of not seeing that color, it'll automatically stop looking. I could also do things like check the parabolic rate of an object getting larger in width and height faster than other objects are not to determine if something is moving while you are moving, but this would be a coding nightmare for me.

[Forever VAC proof] Universal Aimbot 2.0 Beta 1.6

Post a Reply

Similar Threads

Tags for this Thread